🛒 Best Price Today on Amazon
Prime members get fast, free shipping on everything above, plus member-only deals. New members get a 30-day free trial — cancel anytime.
- Quick answer
- IRWIN Hanson Screw Extractor and Drill Bit Set, 10-Piece (11119)
- WYBENZ Screw Extractor and Left Hand Drill Bits Set, 14 Pieces
- IRWIN Impact Screw Grip Double-Ended Screw Extractor Bits, 6-Piece (1876225)
- Alden Grabit Pro Broken Bolt and Damaged Screw Extractor Kit, 4-Piece (8440P)
- IRWIN Hanson Hex Head Multi-Spline Screw Extractor Set, 25-Piece (53227)
- How to choose
- FAQ
- Verdict
A fastener on a generator rarely fails at a convenient moment. It is the carburetor bowl screw with a chewed-up head, the recoil housing bolt that rounds off in its bore, or the manifold stud that snaps flush with the casting after years of heat cycles and damp shed air. Small steel hardware in aluminum and cast housings corrodes in place, and once the head is gone, the repair becomes an extraction job.
One honest warning first. Extractors are hardened steel, and hardened steel is brittle. A snapped extractor lodged in a drilled bolt is worse than the bolt ever was, because few shop tools can cut it. Oil, patience, and a centered pilot hole matter more than force.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
For most generator work, the IRWIN Hanson 10-piece set is the default pick: five spiral flute extractors with a matched left-hand cobalt bit for each size. The WYBENZ 14-piece kit follows the same formula for smaller hardware. If the failure is a stripped screw head rather than a snapped bolt, the IRWIN Screw Grip bits and the Alden Grabit Pro work entirely in a drill: one end prepares the head, the other backs the screw out. For larger studs where you want a wrench and full torque control, the Hanson multi-spline set is the tool.
IRWIN Hanson Screw Extractor and Drill Bit Set, 10-Piece (11119)
This set lives in most small-engine shops. It pairs five spiral flute extractors, EX-1 through EX-5, with five left-hand cobalt drill bits, one matched size per extractor. Drilling the pilot hole with a left-hand bit runs the drill in reverse, and the cutting drag works against the stub the whole time. On lightly seized hardware, the bit alone often walks the broken piece out.
The spiral flutes bite deeper as resistance rises, suiting rusted studs and bolts in steel and cast iron. Each extractor carries its size and drill size etched on the tool. Turn it with a tap wrench and let the flutes wedge and grip.
Specs
– Contents: 10 pieces, EX-1 to EX-5 extractors plus 5 drill bits
– Drill bits: left-hand cobalt, one matched size per extractor
– Fastener range: about 3/16 to 5/8 in across the five sizes
– Markings: size and drill size etched on each tool
– Case: metal index
WYBENZ Screw Extractor and Left Hand Drill Bits Set, 14 Pieces
The WYBENZ kit applies the same drill-then-extract formula in a 14-piece spread aimed at smaller hardware: the stripped screws and snapped bolts holding covers, recoil housings, and carburetor parts on a portable generator. Its bits are cobalt high speed steel, left-hand cut, so the pilot hole step doubles as a first extraction attempt.
The spiral extractors turn by hand with a tap wrench or T-handle, and the reverse-thread flutes pull into the stub as you turn. Fourteen pieces give finer size graduation than a five-size kit, helping on in-between metric hardware from imported engines. Match the extractor so roughly half the flute length engages.
Specs
– Contents: 14 pieces, spiral extractors plus left-hand drill bits
– Drill bits: cobalt high speed steel, left-hand cut
– Extractor style: spiral flute, reverse-thread grip
– Drive: drill in reverse for bits, tap wrench for extractors
IRWIN Impact Screw Grip Double-Ended Screw Extractor Bits, 6-Piece (1876225)
Stripped screw heads are a different failure from snapped bolts, and this set is built for them. Each bit is double-ended and works entirely in a drill or impact driver running in reverse. One end is a drill tip that cuts a clean seat in the ruined head; flip the bit and the serrated extractor end digs into that seat and backs the screw out. Both ends work in reverse, so there is no direction switch to forget.
The bits are M2 high speed steel, extra hardened, with a 1/4 inch hex shank for an impact driver or quick-change chuck. They cover screws No. 4 to No. 14, spanning most housing and panel screws on a generator. Keep the drill slow and push firmly; these bits rely on bite, not speed.
Specs
– Contents: 6 double-ended insert bits
– Material: M2 high speed steel, extra hardened
– Shank: 1/4 in hex, for drills and impact drivers
– Fastener range: screws No. 4 to No. 14
– Design: drill tip one end, serrated extractor tip the other
Alden Grabit Pro Broken Bolt and Damaged Screw Extractor Kit, 4-Piece (8440P)
The Grabit Pro is the other drill-based design, built in the USA from tool steel. Each bit carries a burnishing tip on one end, which dresses a damaged head or the top of a broken bolt into a smooth cone, and a threaded tip on the other end that screws into that cone and pulls the fastener out as the drill keeps turning in reverse. No separate pilot drilling is needed.
Coverage runs from No. 4 to No. 24 screws and No. 10 to 3/8 inch bolts, and Alden rates the bits to drill into fasteners up to grade 8 and class 10.9. Reach for this kit on stripped Phillips and hex heads in shrouds and panels, where a tap-wrench extractor is clumsy.
Specs
– Contents: 4 double-ended bits in a poly case
– Coverage: screws No. 4 to No. 24, bolts No. 10 to 3/8 in
– Shank: 1/4 in hex, quick-connect compatible
– Capability: drills into fasteners up to grade 8, class 10.9
– Design: burnishing tip prepares the head, threaded tip extracts
IRWIN Hanson Hex Head Multi-Spline Screw Extractor Set, 25-Piece (53227)
Multi-spline extractors are a different tool from the screw extractors above. A spiral extractor wedges into a drilled hole and can swell the stub tighter in its threads. A multi-spline extractor is driven into a drilled hole, grips along many fine splines, and turns with a wrench on its hex head. The short body reaches studs in confined spots, and the hex drive gives slow, even torque instead of drill shock.
This 25-piece Hanson set covers fasteners from 1/8 to 5/8 inch in high carbon steel, aimed at demanding work: exhaust studs, head bolts, and frame hardware. Drill on center, seat the spline with light hammer taps, and turn with a socket or wrench.
Specs
– Contents: 25 hex head multi-spline extractors
– Fastener range: 1/8 to 5/8 in
– Material: high carbon steel
– Drive: hex head, turned with a wrench or socket
– Profile: short body for confined spaces
How to choose
Pick the style for the failure in front of you. A snapped bolt or stud with no head calls for a drilled pilot hole and a spiral flute, straight flute, or multi-spline extractor. Spiral flutes grip hardest and suit rusted threads, but the wedging action can expand a stub in a blind hole. Straight flute extractors are tapped in and grip without that wedging, kinder to thin-walled parts and pipe fittings. A stripped head still attached is a job for the double-ended drill-out bits.
Sizing decides most outcomes. The extractor should be roughly half to two-thirds the fastener diameter, and the pilot hole must match it and sit dead center. Center punch first, drill slowly with cutting oil, and always try the left-hand bit on its own first, with the threads soaked in loosening oil and given time to work. Keep flame away from any engine with fuel in the system. If the extractor begins to creak, back off, add oil, and wait.
FAQ
Can an extractor remove a bolt that snapped off flush with the surface?
Yes, that is the normal case for spiral and multi-spline sets. Center punch the stub, drill the pilot hole on center with the matched left-hand bit, and turn the extractor slowly.
Why do extractors snap, and how do I avoid it?
They snap when the extractor is too small for the fastener, turned with side load instead of square to the hole, or forced dry on a seized stub. Use the largest extractor the stub accepts, soak the threads in oil first, and turn evenly with a tap wrench.
Which style is safest for a stud broken in an aluminum housing?
A multi-spline or straight flute extractor, because neither wedges the stub outward as hard as a spiral flute can. Aluminum threads tear easily, so drill on center and use modest torque.
Verdict
Keep the IRWIN Hanson 11119 in the drawer for one set that handles the classic snapped stud or bolt with matched bits and no guesswork. Add the Screw Grip bits or the Grabit Pro kit if stripped screw heads are your usual failure, and step up to the Hanson multi-spline set when the hardware gets bigger and torque needs a wrench, not a drill. The method decides the result: center the hole, soak the threads, size the extractor honestly, never force the turn.





Write Your Review
No reviews yet. Be the first to share your experience!