🛒 Best Price Today on Amazon
Prime members get fast, free shipping on everything above, plus member-only deals. New members get a 30-day free trial — cancel anytime.
For location shoots, a portable power station is often better than a fuel generator because it is silent, has no exhaust and can sit right next to the set. The best choice depends on how much lighting, camera gear and charging you need across a full shooting day. Here is how to plan it.
Quick Picks by Need
| Shoot type | Pick type |
|---|---|
| Run-and-gun interviews | Compact unit with USB-C and a few AC outlets |
| Small crew with LED panels | Mid-size unit with a pure sine wave inverter |
| Multi-camera event | High-capacity unit, possibly expandable |
| Remote outdoor sets | Unit with strong solar input and rugged casing |
| Sound recording and monitors | Quiet, low-noise unit with clean power output |
Build a Gear Power List
Begin with a simple sheet listing every device: cameras, monitors, wireless video, lights, audio recorders, laptops, chargers and any small fans. Write down the wattage from each label and the hours it will run. LED lights can vary widely, so check the actual label on each fixture. Multiply watts by hours to get watt-hours and add everything together.
Then separate continuous load from peaks. Add up what runs at the same time to compare with the inverter continuous rating, and note any gear with a startup surge. Add a safety margin of at least twenty percent for conversion losses and unexpected additions. It is better to arrive with spare capacity than to stop shooting while the light fades.
Clean Power and Silence
Camera and audio gear is sensitive, so prefer a pure sine wave inverter. Poor quality power can cause hum, interference or charger issues. Test your setup before the shoot day by running all your gear together and listening with headphones.
Fans are the usual noise source. Many units have a quiet mode at lower loads, but heavy loads or fast charging may spin the fans faster. Position the unit away from the microphone and out of the shot, and consider keeping it on a stand or crate so cables run neatly.
- Use the DC and USB-C outputs for small devices to reduce inverter loss.
- Keep high-draw lights on their own station if possible.
- Label cables so crew members can swap them quickly.
Ports, Charging and Battery Type
Count the outlets you need. AC outlets run lights and laptops, USB-C power delivery tops up cameras and phones, and 12V ports can run certain accessories. Make sure there are enough ports so you do not need many extension cords.
Battery chemistry matters for a unit that cycles daily. Lithium iron phosphate is widely used for long life and heat tolerance, while other lithium types can be lighter. Check the cycle life and warranty. For recharge, look at wall input speed overnight and solar input for remote days; a unit that charges slowly can leave you short for the next call time.
Safety on Set
- Never run a gasoline generator indoors or inside a closed trailer, and keep exhaust away from the crew and air intakes, because carbon monoxide is deadly.
- Keep cables out of walkways, tape them down and protect them from wet ground.
- Do not cover the vents of the power station with blankets or flags.
- Use proper extension cords with suitable ratings and avoid daisy-chaining power strips.
- For large builds that connect to a building panel, hire a licensed electrician and follow venue rules.
Common Mistakes
- Forgetting the laptop and monitor charging at the end of the day.
- Choosing by capacity and overlooking inverter limits.
- Running power-hungry lights at full brightness longer than needed.
- Not testing the whole kit together before the shoot.
- Leaving the unit in direct sun, which can trigger thermal limits.
Workflow Tips for Long Shooting Days
Treat power as part of the production schedule. Assign one person to monitor the battery levels at set times, such as before lunch and before the final setups, so nobody discovers a flat unit mid-take. Swap batteries and charge small camera packs from the USB-C ports during breaks, and keep the largest loads such as lights on a separate station so a trip does not interrupt audio.
It also helps to record how much energy each setup consumed once the day is over. Next time you can size the unit with real numbers instead of guesses. Keep a few spare adapters, a short extension cord and gaffer tape in the kit, and keep a clear label on each unit showing its charge status at wrap, so the morning crew knows what is ready.
Frequently Asked Questions
Can a power station run continuous lighting all day?
It can if capacity and inverter output match the lights. Add up the fixture wattage and hours, and compare with the battery watt-hours with margin.
Is it quiet enough for recording sound?
It is generally far quieter than a fuel generator, though fans may run. Place it away from microphones and test in advance.
Should I bring more than one unit?
Often yes. Splitting loads between units gives redundancy and keeps sensitive audio gear on its own supply.
Can I recharge between shoot days?
Yes, using wall power overnight or solar on location. Confirm the charge time so the unit is full for the next call.
Final Thoughts
For location work, plan around your gear list rather than marketing numbers. Choose clean sine wave output, ample ports and enough spare capacity for the day, and put safety first with cables and ventilation. A well-chosen power station keeps the set quiet and the crew productive.
Finally, build a short checklist for each shoot: charge status, cable count, spare adapters, and where the unit will sit. A few minutes of preparation prevents most power problems before cameras roll, and it makes each future job easier to plan.
Write Your Review
No reviews yet. Be the first to share your experience!