⏱ 7 min read  ·  ✅ Updated Nov 2026

A reciprocating saw earns its keep when a generator setup has to come apart. Old mounting pads need cutting free, rusted frame rails and exhaust stubs refuse every wrench, conduit runs need trimming during a rewire, and brush creeps in around the outdoor unit until it chokes airflow. No other saw shrugs at all of that in one afternoon.

Our top pick: Milwaukee M18 FUEL SAWZALL Reciprocating Saw (2821-20). Runner-up: DEWALT 20V MAX Reciprocating Saw (DCS380B).

The five picks below span the shapes that matter: two full-size cordless saws, a compact two-handed model, a one-handed saw for tight bays, and a corded saw that never runs out of breath. One truth runs through the list: the blade decides how a cut goes far more than the saw does.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For heavy tear-out, the Milwaukee M18 FUEL SAWZALL is the strongest cordless pick here, with a 1-1/4 inch stroke and 3,000 SPM. The DEWALT DCS380B is the dependable mid-size choice on the 20V MAX platform, while the compact DCS367B suits work between framing and panels. For one-handed cuts inside tight enclosures, pick the Milwaukee M18 FUEL HACKZALL. If the saw will live next to a bench outlet, the Bosch RS325 skips batteries entirely.

Milwaukee M18 FUEL SAWZALL Reciprocating Saw (2821-20)

This is the demolition hammer of the group. The brushless motor drives a 1-1/4 inch stroke at up to 3,000 strokes per minute, and that long stroke clears chips and keeps a demolition blade biting through nail-embedded lumber, old pad framing and stubborn steel brackets.

Milwaukee built in the details that matter during long sessions: a tool-free blade clamp, an adjustable shoe that shifts wear along the blade, a rafter hook, and an LED light for dim enclosure work. At 6.8 pounds bare it is not light, yet the balance keeps it manageable overhead. Feed it a high-output M18 pack for thick metal, because smaller packs fade fast under that load.

Specs
– Platform: Milwaukee M18 18V, bare tool
– Motor: Brushless
– Stroke length: 1-1/4 in
– Speed: 0–3,000 SPM, variable
– Weight: 6.8 lb (tool only)
– Blade change: Tool-free lever clamp, adjustable shoe

DEWALT 20V MAX Reciprocating Saw (DCS380B)

The DCS380B is the long-running workhorse on DEWALT’s 20V MAX platform. Its 1-1/8 inch stroke and variable speed trigger, good for 0 to 3,000 SPM, cover the everyday repair list: trimming conduit, cutting pipe, slicing old mounting hardware, and clearing branches back from an outdoor unit. The trigger feathers well, which helps when a cut needs a gentle entry into thin sheet metal.

Its signature trick is the 4-position blade clamp. The blade can sit in four orientations, so flush cuts along a pad edge or against a frame rail stop being awkward, and changes happen without tools. A pivoting shoe keeps contact on uneven material and stretches blade life. The brushed motor gives up some runtime to brushless rivals, yet it remains a simple, tough saw for owners already holding 20V MAX batteries.

Specs
– Platform: DEWALT 20V MAX, bare tool
– Motor: Brushed
– Stroke length: 1-1/8 in
– Speed: 0–3,000 SPM, variable speed trigger
– Blade clamp: 4-position, tool-free
– Tool length: 18 in

DEWALT 20V MAX XR Compact Reciprocating Saw (DCS367B)

The DCS367B shrinks the saw down to a 14.5 inch body that fits between studs, inside transfer switch enclosures, and under a generator housing where a full-size saw will not go. It keeps a full 1-1/8 inch stroke and reaches 2,900 SPM, so the compact frame does not mean timid cutting; it chews through pipe, lumber and pruning work with genuine pace.

A brushless motor stretches each charge further than the DCS380B manages, and at 5 pounds the saw is easy to hold one-handed for brief cuts, though two hands give better control. The keyless 4-position clamp carries over from its bigger sibling, and an LED light helps inside dark enclosures. It passes more shake through the grip than the smoothest rivals, so let the blade work instead of forcing it.

Specs
– Platform: DEWALT 20V MAX, bare tool
– Motor: Brushless
– Stroke length: 1-1/8 in
– Speed: 0–2,900 SPM, variable speed trigger
– Length and weight: 14.5 in, 5 lb (tool only)
– Blade clamp: Keyless 4-position lever clamp

Milwaukee M18 FUEL HACKZALL Reciprocating Saw (2719-20)

The HACKZALL answers a different question: what about the cuts where only one hand is free? Its inline body and 7/8 inch stroke are built for control in cramped spaces, such as trimming conduit inside a crowded enclosure or cutting pipe between a wall and a tank. The shorter stroke trades raw speed for precision, and cuts wander far less.

Do not mistake it for a toy. The brushless motor spins up to 3,000 SPM, and with a carbide blade fitted it handles threaded rod, angle iron and hardened fasteners that would defeat a lesser compact saw. The QUIK-LOK clamp swaps blades without tools. For pruning around an outdoor unit, one-handed reach into the branches is exactly what this shape was made for.

Specs
– Platform: Milwaukee M18 18V, bare tool
– Motor: Brushless, one-handed inline design
– Stroke length: 7/8 in
– Speed: 0–3,000 SPM, variable
– Tool length: 14 in
– Blade clamp: QUIK-LOK tool-free clamp

Bosch RS325 Reciprocating Saw

The RS325 makes the case for a cord. Its 12 amp motor never fades halfway through a cut and suits long demolition sessions at a fixed site: stripping an old generator room, cutting a pad apart, or working through scrap pipe. Constant orbital action comes built in, which speeds rough wood cutting, though it cannot be switched off, so thin metal work calls for a steadier hand and a fine blade.

At 7 pounds and 17.8 inches long it is trimmer than many corded rivals, and the tool-free blade change keeps the pace up when blades dull. Shock control is the weak point; this saw passes more buzz into the hands than the best cordless models, so gloves and breaks help on long jobs.

Specs
– Power: Corded 120V, 12 amp
– Stroke length: 1 in
– Speed: 0–2,800 SPM, variable speed trigger
– Action: Constant orbital, fixed foot
– Weight: 7 lb
– Blade change: Tool-free clamp

How to choose

Stroke length sets the pace. A 1-1/4 inch stroke moves the most material per pass and shines in demolition, while 1-1/8 inch tools balance speed and control for repair work. Short-stroke one-handed saws near 7/8 inch cut slower yet wander less, which is what tight enclosure work demands.

Speed control matters as much as top speed. Wood and pruning want high SPM; metal wants the trigger feathered low so teeth survive. Orbital action speeds rough wood cutting but can grab in pipe and sheet, so a saw that lets you turn it off earns points for mixed work. Straight action is the safer default when conduit and exhaust tubing fill your list.

Think hard about blade changes, because you will swap blades constantly. Every pick here changes blades without tools and accepts the universal half-inch shank sold everywhere. Stock three blade families: coarse demolition blades for nail-embedded wood, fine bi-metal blades for pipe and conduit, and carbide blades for hardened steel and cast iron.

Finally, weigh the platform honestly. Cordless freedom suits scattered cuts around a property, yet thick metal drains packs fast, so plan on high-capacity batteries and a spare on the charger. A corded saw removes runtime from the equation and suits a fixed workshop.

FAQ

Which blade should I use on generator frame steel?
Reach for a carbide-tooth demolition blade for thick or hardened frame steel, and a bi-metal blade with fine teeth for thin tubing and conduit. Keep the shoe pressed to the work and let the stroke do the cutting.

Is a compact saw enough for demolition?
For light tear-out, pipe and pruning, yes. Compact and one-handed saws handle most repair cuts around a generator. Thick beams, cast iron and long sessions in nail-filled lumber still belong to full-size saws with longer strokes.

Why does my blade keep dulling in metal?
Heat is the usual cause. Slow the trigger down, keep the shoe firm against the material, and use a blade with more teeth per inch for thin stock. A blade that turns blue has been run too fast for too long.

Verdict

Pick the Milwaukee 2821-20 for full-power cordless demolition, the DEWALT DCS380B for proven everyday work on 20V MAX, and the DCS367B when space is tight but the cut still matters. Add the HACKZALL for one-handed precision work, or take the Bosch RS325 if an outlet is always within reach. Choose the blade as carefully as the saw, and every one of these tools will handle demolition and repair duty around your generator for years.

Explore Our Guides & Free Tools