🛒 Best Price Today on Amazon
Prime members get fast, free shipping on everything above, plus member-only deals. New members get a 30-day free trial — cancel anytime.
- Quick answer
- Klein Tools 11055 Klein-Kurve Wire Stripper and Cutter
- Klein Tools 11061 Self-Adjusting Wire Stripper and Cutter
- IRWIN VISE-GRIP 2078300 Self-Adjusting Wire Stripper
- Klein Tools 11063W Katapult Wire Stripper and Cutter
- Knipex 12 62 180 Self-Adjusting Insulation Stripper
- How to choose
- FAQ
- Verdict
Generator wiring work covers three kinds of wire: cord ends you remake when a plug is damaged, thin control wires inside the panel, and heavier leads running to the battery and outlets. A good stripper handles the first two cleanly and never nicks copper, because one nicked strand is a weak point that vibration works loose over time.
Manual strippers use sized holes, one per gauge, and reward a careful hand. Self-adjusting strippers clamp and pull in one squeeze and set their own depth, faster across mixed sizes. One rule sits above every pick below: work only on dead circuits. Shut the set down, disconnect the battery, and prove the circuit dead before a tool touches a conductor.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
The Klein Tools 11055 Klein-Kurve is the manual pick to own first. The Klein Tools 11061 is the self-adjusting workhorse for mixed sizes, and the IRWIN VISE-GRIP 2078300 adds a crimper for terminal work. The Klein Tools 11063W Katapult brings compound leverage for heavier wire, and the Knipex 12 62 180 is the gentle option for fine control wiring.
Klein Tools 11055 Klein-Kurve Wire Stripper and Cutter
The 11055 is the classic manual stripper, and it earns its place because it makes you pick the right hole every time. Each hole is ground for one gauge, marked for solid and for stranded wire, since stranded conductor needs the larger opening. Use one hole too small and the jaws shave copper; use the correct hole and the insulation slides off with every strand intact.
The serrated nose grips and bends wire for hooks around terminal screws, a looping hole forms tidy loops, and the jaw shears 6-32 and 8-32 screws when a panel screw needs shortening. The range tops out at 10 AWG solid and there is no crimper: a dedicated stripper and cutter, light at 5.4 ounces, made in the USA.
Specs
- Strips and cuts: 10-18 AWG solid, 12-20 AWG stranded
- Precision-ground stripping holes; serrated gripping nose
- Shears 6-32 and 8-32 screws; wire looping hole
- Overall length 7.4 in; weight 5.4 oz
- Not insulated; never use on live circuits
Klein Tools 11061 Self-Adjusting Wire Stripper and Cutter
The 11061 works the other way: one squeeze and the head grips, rings the insulation, and pulls it free, sizing itself to the wire as it goes. It covers 10-20 AWG solid and 12-22 AWG stranded, spanning nearly every control wire, switch lead, and cord conductor on a typical portable or standby set.
A tension dial lets you back the bite off for thin or soft insulation, and an adjustable stop sets a repeatable strip length. It also strips 12/2 and 14/2 Romex-style cable, and the handle cutter takes wire up to 8 AWG solid. On delicate wires the head can still bite a strand with tension left high, so test on scrap first.
Specs
- Strips and cuts: 10-20 AWG solid, 12-22 AWG stranded
- Also strips 12/2 and 14/2 Romex and NM sheathed cable
- Self-adjusting head with tension adjustment dial
- Adjustable stopper for repeatable strip lengths
- Overall length 8.25 in; weight 12.6 oz
IRWIN VISE-GRIP 2078300 Self-Adjusting Wire Stripper
The 2078300 is the combo tool of this group. It self-adjusts across 10-24 AWG, the widest span here. A swivel knob gives micro-adjustment for gauges under 20 AWG, easing blade pressure so thin strands come through whole.
Below the jaw sits a crimper for insulated and non-insulated terminals from 10-22 AWG, so one tool can strip a lead and crimp on a fresh ring terminal without a trip to the bench. It is a squeeze die, fine for light terminals but no match for a dedicated lug crimper. An adjustable stopper keeps strip lengths even, and the wide jaw and ProTouch grips suit gloved hands.
Specs
- Self-adjusting strip range: 10-24 AWG
- Micro-adjustment swivel knob for wire under 20 AWG
- Crimps 10-22 AWG insulated and non-insulated terminals
- Adjustable stopper for consistent strip lengths
- Overall length 8 in; weight about 12 oz
Klein Tools 11063W Katapult Wire Stripper and Cutter
The Katapult is built for the heavy end of the range. Its compound-action head grips and pulls in one squeeze, with leverage that makes 8, 10, and 12 AWG conductors feel routine. It strips 8-20 AWG solid and 10-22 AWG stranded and can take off up to a full inch of insulation in one pass, suiting longer landings on larger terminals.
The cast alloy chassis is the point of the design: where lighter self-adjusting tools flex on thick insulation, this head stays square, so the cut ring stays even and strands stay unmarked. A built-in cutting hole trims wire cleanly, and the blades are replaceable. At 12 ounces it is more tool than thin control wires need, so keep it for cord ends and heavier runs.
Specs
- Strips and cuts: 8-20 AWG solid, 10-22 AWG stranded
- Compound-action head grips and strips in one squeeze
- Removes up to 1 in of insulation per pass
- Replaceable stripping blades; hold-open spring
- Overall length 6.6 in; weight 12 oz
Knipex 12 62 180 Self-Adjusting Insulation Stripper
The 12 62 180 is the precision pick for control wiring. It self-adjusts across 0.2 to 6 square millimetres, roughly 24 to 10 AWG, and its blade shape stops at the conductor surface, which is why it is kind to the fine multi-strand wires used for sensors, governors, and switch looms. A fine-adjustment slider corrects cutting depth for soft or thick insulation outside the usual range.
The length stop adjusts from 6 to 18 millimetres, and the narrow head reaches into crowded enclosures. The fiberglass-reinforced body keeps it near 5.3 ounces, and the oil-hardened blades swap out when worn. Heavy cord conductors sit at its ceiling, and there is no crimper, but nothing else here strips thin wire as gently.
Specs
- Stripping capacity: 0.2-6.0 mm², about 24-10 AWG
- Self-adjusting blades shaped to protect fine strands
- Adjustable length stop, 6-18 mm
- Cutter for copper and aluminium up to 2.5 mm²
- Fiberglass-reinforced body; length 180 mm; weight about 151 g
How to choose
Match the tool to the wire you strip most. If most work is cord ends and outlet leads in 12 to 16 AWG, a manual tool like the 11055 gives the cleanest result. If you move across many gauges at once, a self-adjusting tool saves real time, and a tension dial is worth having for thin insulation.
Respect the hole on a manual stripper. Solid and stranded wire of the same gauge need different openings, and one size too small is how strands get nicked. A nicked strand carries less current, heats at the joint, and breaks early under vibration. Check every stripped end against the light; if you see a bright shaved flat on the copper, cut it off and strip again.
Keep the jobs separate. These tools strip insulation; they are not lug crimpers. Heavy battery cables need a proper cable cutter and a lug crimper sized for the barrel, and forcing a stripper into that work ruins tool and cable alike. None of these tools is insulated either: shut down, disconnect, and test before you strip, every time.
FAQ
Can I strip wire with the generator battery still connected?
No. Disconnect the battery and confirm the circuit is dead first. A short across a battery lead can weld a tool and burn hands in a blink, and none of these strippers is insulated.
Why do strands keep breaking on thin control wires?
The tool is biting too deep. On a manual stripper you are likely one hole too small; stranded wire needs the larger opening. On a self-adjusting tool, ease the tension back and test on scrap until the insulation alone comes away.
Do I need a separate crimper if my stripper has one built in?
For small terminals, a built-in crimper like the one on the IRWIN is fine. For battery lugs and heavy cable ends, use a dedicated lug crimper with the correct die; a weak crimp on a high-current lead overheats in service.
How long should the bare end be?
Long enough to fill the terminal barrel or wrap the screw fully, with no bare copper showing outside the connection and no insulation trapped inside it. A length stop keeps every end in a row identical.
Verdict
Own one manual and one self-adjusting stripper and nearly every generator wiring job is covered. The Klein 11055 handles cord and outlet work with care, the Klein 11061 or IRWIN 2078300 speeds through mixed gauges, the Katapult takes heavy conductors, and the Knipex protects fine control wires. Match the hole to the wire, check each end for nicks, and never strip a live circuit.





Write Your Review
No reviews yet. Be the first to share your experience!