⏱ 7 min read  ·  ✅ Updated Nov 2026

Pull the blower housing, recoil cover or side panel off a small engine and you will meet six-point screws everywhere. Makers like them because the six-lobed recess spreads torque across a wide contact patch, so the screws hold tight through years of heat cycles and shaking, yet they defeat the flat and Phillips drivers in a general tool kit.

Our top pick: TEKTON 3/8 Inch Drive Long Six-Point Bit Socket Set, 12-Piece (SHB91305). Runner-up: LEXIVON Tamper Proof Six-Point Bit Socket Set, 13-Piece (LX-146).

The catch is variety, though. One cover screw sits proud, the next hides at the bottom of a deep well, and a third carries a center pin a plain bit cannot enter. Sets answer that variety in different ways: long bit sockets for recessed screws, security bits for pinned heads, short insert bits for tight corners, and female E-sockets for external heads.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

Short on time? The TEKTON long bit socket set is the first pick for recessed housing screws, its extended bits reaching down deep wells on a single 3/8-inch drive. The LEXIVON set handles pinned security screws, CASOMAN’s kit adds female E-sockets for external heads, the GEARWRENCH master set pairs six-point bits with a full hex range, and the NEIKO security kit packs the widest spread of insert bits for tight quarters.

TEKTON 3/8 Inch Drive Long Six-Point Bit Socket Set, 12-Piece (SHB91305)

Recessed screws are the recurring headache on engine covers: the head sits at the bottom of a molded well, and a short bit socket bottoms out before the tip seats. TEKTON answers with length. Every bit here is a long pattern on a 3/8-inch drive, so the slim shaft drops into the well while the ratchet stays clear of the housing ribs.

The range runs T10 through T60, blanketing the T20 to T50 span small engines use most. The bits are S2 steel, a step up in toughness from plain chrome vanadium, resisting the rounding that ruins a screw head when a bit cams out under load. A molded case keeps the dozen sockets in size order.

Specs
– 12 long bit sockets on a single 3/8-inch drive
– Sizes: T10, T15, T20, T25, T27, T30, T40, T45, T47, T50, T55, T60
– Bits made from S2 steel
– Long pattern for recessed and deep-well screws
– Molded storage case included

LEXIVON Tamper Proof Six-Point Bit Socket Set, 13-Piece (LX-146)

Some covers use security screws with a small pin standing in the middle of the recess, and a solid bit simply will not seat. This LEXIVON set is built for those heads: every bit is drilled with a center hole that slips over the pin, so pinned and plain screws alike turn with the same kit.

The 13 pieces split across three drive sizes, the smaller bits on 1/4-inch drive, the mid range on 3/8-inch, and a T60H on 1/2-inch for the heaviest case bolts. The bits are drop-forged S2 steel hardened to 60–62 HRC with a zinc phosphate finish, on chrome vanadium socket bases. That hardness matters on pinned screws, where the drilled tip has thinner walls and a soft bit twists or cracks.

Specs
– 13 security bit sockets with center holes for pinned screws
– 1/4-inch drive: T8H, T10H, T15H, T20H, T25H, T27H, T30H
– 3/8-inch drive: T40H, T45H, T47H, T50H, T55H; 1/2-inch drive: T60H
– S2 steel bits hardened to 60–62 HRC, zinc phosphate finish
– Storage case with stamped size markings

CASOMAN 32-Piece Six-Point Bit Socket and Female External Socket Set

Most bit sets only handle internal recesses, yet some housings fasten with external six-point heads, the inverse shape that needs a female socket. This CASOMAN kit covers both directions in one case: 14 bit sockets for recessed screws and 13 female E-sockets for external heads, plus five adapters for impact drivers and mixed drives.

The bit sockets run T8 to T70 and the E-sockets E4 to E24, spanning the sizes found on generator frames and engine covers. Bits are S2 steel and the sockets chrome vanadium with a black phosphate finish that shrugs off garage grime. Pieces spread across 1/4, 3/8 and 1/2-inch drives, so small trim screws and stubborn frame bolts both get a suitable handle.

Specs
– 32 pieces: 14 bit sockets, 13 female E-sockets, 5 adapters
– Bit sockets T8 to T70; E-sockets E4 to E24
– S2 steel bits, chrome vanadium sockets, black phosphate finish
– Mixed 1/4, 3/8 and 1/2-inch drives
– Adapters included for driver and impact use

GEARWRENCH 84-Piece Master Hex and Six-Point Bit Socket Set (80742)

A generator bench rarely turns one fastener family alone: a housing comes off with six-point screws, then the carburetor and mounts ask for hex bits in metric and SAE. This GEARWRENCH master set puts both families in one blow-mold case, 84 pieces across 1/4, 3/8 and 1/2-inch drives.

The bits are S2 steel in alloy steel socket bases with a full polish chrome finish that wipes clean after greasy work. Sizes are hard-stamped into the sockets, and each piece sits in a labeled pocket, which speeds up the grab for a T25 or T30 mid-teardown.

Specs
– 84-piece master set of hex and six-point bit sockets
– S2 steel bits in alloy steel socket bases
– Full polish chrome finish
– Hard-stamped size markings, labeled blow-mold case
– Mixed 1/4, 3/8 and 1/2-inch drives

NEIKO 10048A Security Bit Set, 100-Piece

When a screw sits in a tight corner where a ratchet head cannot swing, short insert bits earn their keep. This NEIKO kit packs 100 pieces around the 1/4-inch hex shank format: nine standard six-point bits and nine security six-point bits, each running T8 to T40, alongside hex, Phillips, slotted, Pozi, square, spanner, tri-wing, clutch and spline bits.

The bits are chrome vanadium steel and work in any standard bit holder, including the magnetic holder and adapters in the case. A magnetic holder grips the screw while you guide it into a deep or blind hole, and holds the bit firmly during one-handed work under a cover. The flat case slides into a drawer or service bag, though the range topping out at T40 means pairing it with a socket set for the largest case bolts.

Specs
– 100 pieces built around 1/4-inch hex shank insert bits
– 9 standard and 9 security six-point bits, T8 to T40
– Chrome vanadium steel construction
– Magnetic bit holder and adapters included
– Flat storage case with labeled slots

How to choose

Match the set to the screws you actually meet. Most covers and housings live between T20 and T50, so confirm those sizes are complete, with no gaps at T25, T27 and T30, the trio that shows up again and again on blower housings and side panels.

Decide between bit sockets and insert bits. Bit sockets on a ratchet deliver the torque for case bolts and screws that have sat through seasons of heat. Insert bits on a 1/4-inch hex shank reach tight corners and pair with magnetic holders that keep screws from dropping into the housing. Check the screw heads for a center pin before buying, since a pin makes drilled security bits mandatory, and favor long-pattern bits where heads sit in deep wells. Finally, weigh the steel: S2 bits hold their edges longer than plain chrome vanadium.

FAQ

Which T-sizes do generator covers use most?

Most housings and panels fall between T20 and T50, with T25, T27 and T30 appearing most often on blower housings and side panels. A set covering T10 to T50 without gaps handles nearly every job.

Can security bits turn plain screws?

Yes. A security bit has a center hole drilled into the tip, and that hole changes nothing on a plain head, so one security set covers both kinds. The reverse does not hold: a solid bit cannot seat on a pinned head.

Are long bit sockets worth it for engine work?

For recessed screws, yes. Housing screws often sit at the bottom of deep molded wells, and a short bit socket fouls the well wall before the tip seats. Long bits reach the head cleanly and keep the ratchet clear of ribs.

Do I need female E-sockets as well?

Only if your equipment uses external six-point heads, where the raised shape on the bolt needs a female socket rather than a bit. Some frames mix both styles, where a combined kit like the CASOMAN set saves a second purchase.

Verdict

For most generator owners, the TEKTON long bit socket set is the core buy: S2 steel, the full T10 to T60 span and the reach recessed housing screws demand. Add the LEXIVON security set if pinned screws appear on your machines, or step up to the GEARWRENCH master case for a bench that also turns hex hardware daily. The CASOMAN kit covers external heads, and the NEIKO set is the compact answer for tight corners.

Explore Our Guides & Free Tools