🛒 Best Price Today on Amazon
Prime members get fast, free shipping on everything above, plus member-only deals. New members get a 30-day free trial — cancel anytime.
- Quick answer
- Painless Performance 40140 Body and Engine Ground Strap Kit
- Standard Motor Products B12G Ground Strap
- 12-Piece Tinned Copper Braided Ground Strap Set, 10/15/20 Inch
- Auerllcy Ground Straps Kit, 10/12 Inch, 12-Piece Set
- OXDFK 6-Piece Universal Braided Copper Ground Strap Set, 12 Inch
- How to choose
- FAQ
- Verdict
A ground strap is a humble length of braided copper, yet it carries the return path for some of the heaviest current in a machine. On a generator, straps bond the engine block to the frame and the frame to the equipment case, giving fault and cranking current a clean, low-resistance route home. Braid beats solid bar here because it flexes with vibration instead of cracking.
When a strap corrodes, the symptoms rarely point at the strap. Slow cranking that mimics a tired battery, flickering panel lamps and control boards that reset under load are classic signs of a bond that has gone green and resistive. The five straps below range from a full re-bonding kit to a single factory-style replacement.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
For a complete re-bond in one box, the Painless Performance 40140 kit pairs one heavy 1/0 gauge strap with three lighter body straps and hardware. For a single factory-style replacement, the Standard Motor Products B12G follows original-equipment patterns. If you maintain several machines, the 12-piece tinned copper sets keep the right length on hand, and the OXDFK set covers the common 12 inch span.
Painless Performance 40140 Body and Engine Ground Strap Kit
Painless built this kit for the job most projects actually need: bonding several points at once rather than fixing a single link. The headline piece is a 14 inch strap in 1/0 gauge braided copper, sized for the main engine-to-frame path where cranking current flows. Three 11 inch straps in 10 gauge handle lighter case-to-frame bonds.
The straps arrive terminated, and the box includes self-tapping screws and serrated washers, which suits a fresh install on equipment that never had a proper bond. The washers matter: their teeth bite through paint and light oxide so the eyelet meets bare metal. The heavy strap is round cable-style rather than flat braid, which routes easily around brackets. Keep it short and direct.
Specs
– Contents: one 14 in 1/0 gauge strap, three 11 in 10 gauge straps
– Construction: braided copper, factory-crimped eyelets
– Hardware: self-tapping screws and serrated washers included
– Best for: full engine, frame and case bonding in one job
Standard Motor Products B12G Ground Strap
The B12G is the traditional flat braid replacement sold through normal parts channels, and it follows original-equipment patterns closely enough to carry factory interchange numbers for GM and Honda applications. It suits any small engine, standby unit or vehicle needing one strap swapped like for like.
Its flat braid lies flush against a machined boss or frame pad, spreading clamping force across the eyelet so the joint stays stable as the machine vibrates. The eyelets are punched for common bolt sizes, so fitting is usually a case of cleaning the faces and bolting down. Length is the main thing to check, since a single strap gives one fixed span: measure the old strap hole to hole, and keep the new one relaxed rather than pulled tight, because tension works eyelets loose over time.
Specs
– Part number: B12G
– Construction: flat braided copper, punched eyelets
– Interchange: GM 6295562, Honda 32620-671-000 patterns
– Best for: single like-for-like strap replacement
12-Piece Tinned Copper Braided Ground Strap Set, 10/15/20 Inch
This assortment is aimed at the workbench rather than a single machine. Twelve straps in 10, 15 and 20 inch lengths mean the right span is usually in the box when a frame, welder case or compressor skid needs a bond, and the ring terminals arrive factory crimped.
Every strap is tinned copper, and the tinning earns its keep outdoors and in damp enclosures. Bare copper grows a green oxide skin that creeps under the eyelet and raises resistance; the tin layer slows that process and keeps the contact face bright far longer. The braid is a medium-weight flat weave, well matched to bonding and mid-level return paths rather than the main cranking run on a large engine, where you should double up two straps or step up to the Painless 1/0 gauge strap.
Specs
– Quantity: 12 straps per set
– Lengths: 10 in, 15 in and 20 in assortment
– Material: tinned copper braid, ring terminals
– Best for: workshops maintaining several machines
Auerllcy Ground Straps Kit, 10/12 Inch, 12-Piece Set
Auerllcy’s kit concentrates on the two spans that come up most often, 10 and 12 inches. Twelve braided copper straps in those lengths suit battery-to-block bonds, frame jumpers on compact generators and case bonds on bench equipment, where longer straps would only add slack to coil and chafe.
The straps are flat braid with closed ring terminals, so each presents a wide contact patch at the bolt. Once paint is cleaned off the spot, the eyelet seats evenly and a serrated washer can bite around its full ring. Test-fit each run before bolting down, and never stretch a short strap to reach: a strained eyelet is the first place a bond fails.
Specs
– Quantity: 12 straps per set
– Lengths: 10 in and 12 in
– Model: Ground Straps-12 (GS12)
– Construction: braided copper, flat profile, ring terminals
OXDFK 6-Piece Universal Braided Copper Ground Strap Set, 12 Inch
The OXDFK set keeps things simple: six straps, all 12 inches long, all in tinned braided copper with terminal plugs at each end. Twelve inches covers most block-to-frame jumps on small and mid-size machines, so a uniform set removes the guesswork when renewing every bond on one generator.
On equipment that lives outdoors, the tin finish keeps the braid flexible and the eyelets clean far longer than bare copper, which stiffens as oxide builds between the strands. Six identical straps also make tidy spares: fit four or five and keep the rest for the day a terminal cracks. Check eyelet hole size against your bolts first, as compact engines use smaller fasteners than vehicle chassis work.
Specs
– Quantity: 6 straps per set
– Length: 12 in each
– Material: tinned braided copper
– Terminals: pre-fitted plugs at both ends
How to choose
Begin with the path the strap must serve. The main engine-to-frame bond carries cranking current, so it wants the heaviest gauge and shortest run; a 1/0 gauge strap like the one in the Painless kit is the right scale. Secondary bonds carry far less, and a medium flat braid is plenty.
Next, measure hole to hole and choose a length that fits with a gentle curve to spare. Check eyelet hole size against your bolts too: a loose eyelet concentrates contact on one edge and heats under load.
Material choice comes down to environment. Tinned copper is the safer default for outdoor generators and damp shops because it resists the green corrosion that lifts resistance at the joint. Bare copper conducts marginally better on day one but needs a protected indoor setting to stay that way. Either way, fitting decides the result: clean both mounting faces to bright bare metal, use a serrated washer so it bites through any remaining film, and torque the fastener firmly. A strap bolted over paint barely conducts.
One honest limit: a strap bonds parts of the machine to each other; it is not a substitute for a proper earth rod where a separately derived system calls for one. Follow the generator manual and local code for earthing.
FAQ
How do I know a ground strap has gone bad?
Look for green or white crust at the eyelets, stiff or frayed braid, and symptoms such as slow cranking or controls that reset under load. A voltage drop test across the strap while cranking settles it: a healthy strap shows almost no drop.
Can I fit a longer strap than the original?
A little extra length is fine if it loops in a smooth curve and cannot chafe on edges or hot parts. Never fit a shorter strap that pulls tight, and avoid coils of spare strap, which add resistance.
Is tinned copper better than bare copper for a generator?
For most generator duty, yes. The tin layer slows oxide growth at the joint, especially outdoors. Bare copper suits clean, dry, indoor equipment where joints stay bright.
Where should straps go on a standby generator?
Bond the engine block to the frame, the frame to the alternator case, and the control enclosure to the frame, keeping each run short and direct. Follow the manual for the earth connection itself, since that side is governed by code.
Verdict
Most bonding jobs are won or lost at the contact faces. Choose the Painless 40140 kit when a machine needs a full set of bonds with one heavy strap for the main path, pick the B12G for a single factory-style swap, and keep a tinned multi-piece set on the shelf for several machines. Clean metal, a serrated washer and a short, direct run make any of them perform as intended.





Write Your Review
No reviews yet. Be the first to share your experience!