⏱ 7 min read  ·  ✅ Updated Nov 2026

🛒 Best Price Today on Amazon

Prime members get fast, free shipping on everything above, plus member-only deals. New members get a 30-day free trial — cancel anytime.

Start 30-Day Prime Free Trial →See Today’s Amazon Deals

A step bit earns its place in a generator toolbox whenever a panel or housing needs one more clean hole. Adding a gauge, switch or cable gland with a twist drill usually ends with a grabbed edge, a triangular hole and a burr. A stepped cone bit walks up through marked sizes instead, shaving metal at each step and leaving a round hole largely deburred on both faces.

Our top pick: IRWIN Unibit Step Drill Bit 15101. Runner-up: Milwaukee Step Drill Bit 48-89-9209.

The five picks below cover work from small holes in a junction box lid up to conduit-size openings in a transfer panel. They differ in coating, flute shape and shank style, which decide edge life and behaviour in a drill or impact driver.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

The IRWIN Unibit 15101 covers 1/8 to 1/2 inch for daily panel work. The Milwaukee 48-89-9209 suits conduit entries at 7/8 and 1-1/8 inch. The DEWALT DWA1790IR set fits impact drivers, the NEIKO 10197A set gives the widest coverage in one case, and the NEIKO 10194A is a single large bit reaching 1-3/8 inch.

IRWIN Unibit Step Drill Bit 15101

The Unibit name is the original one for this tool shape, and the 15101 is the compact titanium nitride coated version for small holes. It climbs from 1/8 inch to 1/2 inch in fine increments, matching holes for panel lamps, switches, sensor threads and cable glands.

A single straight flute does the cutting, and that simple geometry is easy to control at low speed in thin steel and aluminium. The SpeedPoint tip is self-piloting, so the bit bites where the punch mark sits instead of skating across a painted panel, and each step is etched with its size.

The titanium nitride layer lowers friction and helps the edge hold up through repeated holes in enclosure lids. Add cutting oil and this bit leaves a tidy edge.

Specs
– Hole range: 1/8 inch to 1/2 inch
– Steps: 13 hole sizes
– Material: high speed steel with titanium nitride coating
– Flute: single straight flute with SpeedPoint tip
– Shank: 1/4 inch hex

Milwaukee Step Drill Bit 48-89-9209

Milwaukee built this bit, often called the number 9, for two hole sizes cut again and again: 7/8 inch and 1-1/8 inch. Those are the entries for half inch and three quarter inch conduit, the scale of cable entries on larger generator housings.

The black oxide finish resists rust in a damp shed and runs cool in cordless drills, where this bit is tuned to work. A dual flute design clears chips from both sides of the cone, so the bit keeps cutting instead of packing swarf into the hole as diameter grows.

Laser etched marks sit in the flutes where oil and chips do not hide them, and the three flat shank grips firmly in a keyless chuck. For enlarging a hole to take a conduit fitting, this is the most direct tool here.

Specs
– Hole sizes: 7/8 inch and 1-1/8 inch
– Material: high speed steel, black oxide finish
– Flute: dual flute for faster chip clearing
– Shank: 3-flat secure grip
– Marks: laser etched size marks in the flute

DEWALT Step Drill Bit Set DWA1790IR

This three piece set is made for impact drivers, with quarter inch hex shanks that lock into a quick change chuck. Between the three bits you get 31 hole sizes from 1/8 inch to 7/8 inch, enough for nearly every switch, lamp and gland on a home backup setup.

Each bit uses a spiral dual flute ground into titanium nitride coated steel. The spiral pulls chips out of the cut, keeping the hole wall smooth and reducing chatter in thin stock. Split point tips begin cutting on contact, so a centre punch mark is all the guidance needed.

Laser engraved numbers mark each step, and the titanium layer shrugs off the heat of repeated holes in steel boxes. If your panel work happens with the impact driver already in hand, this set removes the tool swap.

Specs
– Pieces: 3 step bits in one set
– Coverage: 31 hole sizes, 1/8 inch to 7/8 inch
– Material: titanium nitride coated steel
– Flute: spiral dual flute
– Shank: 1/4 inch hex, impact ready
– Tips: split point, self-piloting

NEIKO Step Drill Bit Set 10197A

The NEIKO 10197A set is the coverage pick: five titanium coated bits holding 50 SAE hole sizes, from 1/8 inch up to 1-3/8 inch. One case replaces a drawer of individual bits for odd jobs like opening a tank panel for a gauge or adding a vent hole in a battery box.

Two flute geometry runs through the set, giving a balance of speed and control for mixed work in steel, brass, aluminium and plastic. The bits ride in a marked aluminium case, so the bit you need is found by reading the lid.

Coated high speed steel will not match cobalt for life in stainless, and this set aims at general shop use rather than daily trade volume. For a home setup that sees a few panel jobs a year, breadth of sizes matters more than marathon edge life.

Specs
– Pieces: 5 step bits with aluminium case
– Coverage: 50 hole sizes, 1/8 inch to 1-3/8 inch
– Material: titanium coated high speed steel
– Flute: two flute design
– Shank: hex shanks for drill chucks

NEIKO Titanium Step Drill Bit 10194A

Some jobs need one big hole rather than a case of options, and the 10194A climbs ten steps from 1/4 inch to 1-3/8 inch. That range covers the largest conduit and gland entries on standby enclosures without changing tools mid hole.

The cone is titanium coated alloy steel with a 135 degree split point that centres itself in a punched mark. A three flat shank keeps the bit from slipping in the chuck when the wide steps bite, which is when torque peaks.

Because the steps are tall, feed pressure needs a light touch near the final size; let the edge shave rather than forcing the cone through. Run slowly with cutting oil and the steps stay round.

Specs
– Hole range: 1/4 inch to 1-3/8 inch
– Steps: 10 hole sizes
– Material: titanium coated high speed alloy steel
– Tip: 135 degree split point
– Shank: 3-flat

How to choose

Match the range first. Small switch and lamp holes live between 1/8 and 1/2 inch, while conduit entries jump to 7/8 inch and above. A bit that tops out below your biggest fitting is dead weight, and one huge bit is clumsy for small work.

Coating and base metal decide edge life. Titanium nitride and black oxide are coatings over high speed steel; they cut friction and slow wear in mild steel and aluminium. Cobalt bits take more hunting down, but the alloy holds an edge in stainless far longer, so regular stainless work justifies the search.

Flute shape changes feel. Straight single flutes are calm and easy to meter step by step. Spiral and dual flutes clear chips faster and suit cordless drills and impact drivers, but they can pull the bit forward, so brace the work and ease off near the target step. Hex shanks suit impact drivers; three flat shanks grip best in a plain chuck.

Respect the thin stock limit. A step bit is happy in material up to about an eighth of an inch thick, since each step needs to pass fully through to size and deburr the hole. Thicker plate belongs to annular cutters or a punch. Slow speed, steady pressure and cutting oil keep edges clean.

FAQ

Can a step bit drill stainless steel?
Yes, in thin gauges, with low speed and cutting oil. Coated steel dulls faster in stainless, so cobalt is the better choice if stainless panels are regular work.

Do I need a pilot hole first?
Usually not. The split point and SpeedPoint tips here are self-piloting and begin on a centre punch mark. A small pilot hole can help on the largest sizes.

Why did my hole come out oversized?
The bit advanced one step too far. Watch the etched marks, count steps from the tip, and stop the moment the step you need passes through the sheet. A test hole in scrap settles the count first.

How do I keep the bit sharp for longer?
Run slowly, use cutting oil on steel, clear chips often and never lean on the drill. Heat kills the edge, and nearly all of it comes from speed and dry cutting.

Verdict

For most panel work, the IRWIN 15101 handles small holes with control, and the Milwaukee 48-89-9209 takes the conduit sizes. Choose the DEWALT set if an impact driver is your daily tool, the NEIKO 10197A set for widest coverage, and the NEIKO 10194A when one large bit must reach 1-3/8 inch. Keep speed low and oil handy, and holes come out round.

Explore Our Guides & Free Tools