⏱ 7 min read  ·  ✅ Updated Nov 2026

A hole saw cuts a true round opening in a single pass, a job no twist bit or jigsaw does as cleanly. For generator work that means a vent in a plywood enclosure, a gauge hole in a control panel, or a cable pass-through in a shed wall. The cup, teeth, and arbor decide whether that hole comes out clean or torn.

Our top pick: Milwaukee 49-22-4025 Hole Dozer Hole Saw Kit, 13-Piece. Runner-up: DEWALT Hole Saw Kit, 14-Piece, D180005.

The five kits below cover the main blade families. Bi-metal suits wood, plastic, and thin metal. Carbide holds an edge longer in abrasive and tougher metal. Diamond grit grinds tile and masonry. Match blade to material and run big cups slowly.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For most enclosures and panels, the Milwaukee Hole Dozer 13-Piece kit is the balanced pick. The DEWALT 14-Piece kit adds deeper cups for thick lumber. The LENOX 26-Piece kit gives the widest size range. Choose the LENOX Carbide Tipped 11-Piece kit for fiber cement, cast iron, or frequent metal. Pick the Spyder 11-Piece kit if fast core ejection matters most.

Milwaukee 49-22-4025 Hole Dozer Hole Saw Kit, 13-Piece

Milwaukee built the Hole Dozer around a bi-metal cup with a hardened edge bonded to a flexible body. That mix matters when a cup moves from pine framing to a thin steel panel in one afternoon. Teeth resist chipping on a nail, and the body flexes rather than cracking when the drill binds.

This 13-piece set covers common enclosure and conduit sizes, and side slots help lever out a wood plug. Pin-drive arbors keep larger cups from spinning loose, and depth suits standard panels. Run it low on metal, add oil on steel, and lift often to clear chips. A slow feed with oil gives many more clean holes than forcing the drill.

Specs
– Blade material: Bi-metal high speed steel edge
– Model: 49-22-4025, 13 pieces
– Use: Wood, plastic, drywall, thin metal
– Arbor: Pin-drive arbors with pilot bits included
– Feature: Side slots for plug removal
– Case: Molded storage case included

DEWALT Hole Saw Kit, 14-Piece, D180005

DEWALT takes a different angle with deeper cups. These saws cut deeper than many general kits, so a hole through thick lumber or a doubled enclosure wall can finish in one pass. That depth leaves a smoother wall inside the hole, which helps when a cable or grommet needs to sit flush.

The set holds 11 bi-metal saws from small gauge sizes up to vent and conduit sizes. Two quick change mandrels are included, one for small cups and one for large, plus pilot bits. Swap cups with a simple collar move, without hunting for a wrench. Clamp thin metal flat, keep the drill square, and let the pilot guide the cup until teeth score a full circle before adding pressure.

Specs
– Blade material: Bi-metal high speed steel
– Model: D180005, 14 pieces, 11 saws
– Sizes: 3/4 inch to 2-1/2 inch saws
– Mandrels: Small and large quick change mandrels
– Cutting depth: Deep cups for thick stock in one pass
– Case: Durable molded case included

LENOX 26-Piece Bi-Metal Hole Saw Kit, 30804-2000G

If you cut many diameters, this LENOX set is the wide-coverage option. With more cups than the other bi-metal kits here, it reduces the chance a job stalls because the one size you need is missing. That breadth suits a bench handling housings, junction boxes, locksets, and vent work across wood and metal.

The bi-metal build pairs a hard tooth edge with a tougher body, handling slight wobble from a handheld drill better than a brittle cup. Thicker cup walls help limit tooth loss on metal, and stepped side slots give a screwdriver leverage for plug removal. Use the included arbors, keep pilots sharp, and replace a bent pilot at once, since a bent pilot makes every hole wander.

Specs
– Blade material: Bi-metal construction
– Model: 30804-2000G, 26 pieces
– Use: Wood, metal, plastic, drywall
– Arbors: Arbors and pilot bits included
– Feature: Wide size coverage for shop use
– Case: Storage case included

LENOX Tools Hole Saw Kit, Carbide Tipped, 11-Piece, LXAH3GSET11

Carbide changes the equation when material fights back. Here carbide teeth are welded to the edge, giving a much harder tooth than bi-metal. That pays off in fiber cement, plaster, cast iron, and repeated metal cuts, where bi-metal would dull and tear instead of cut.

Carbide is hard but less forgiving of shock, so steady feed and a firm grip matter. Avoid dropping the cup on concrete and do not let the drill chatter in the hole. With smooth feed these teeth hold size well and leave a cleaner edge in abrasive stock. Keep speeds low on metal and use cutting oil on steel.

Specs
– Blade material: Carbide tipped teeth
– Model: LXAH3GSET11, 11 pieces
– Use: Wood, metal, cast iron, fiber cement, plaster
– Arbors: 1L and 2L arbors included
– Pilot bits: Two pilot drills included
– Case: Durable carrying case included

Spyder 11-Piece Bi-Metal Hole Saw Kit, Rapid Core Eject

Spyder focused on the most annoying part of hole saw work: getting the plug out. Its Rapid Core Eject arbor lets you slide the cup forward and push the core out, instead of prying through side slots. For a row of vent holes in an enclosure, that saving repeats and keeps the job moving.

The kit holds seven bi-metal saws for panels and pass-throughs, plus Hex8 and Hex10 arbors and pilot bits. Variable pitch teeth cut wood, metal, and plastic with less vibration, helping the drill stay on line in thin sheet. Cups also fit universal arbors. Thin steel cuts well at low speed with oil, but thick stainless shortens bi-metal life. Save that for carbide.

Specs
– Blade material: Bi-metal steel, variable pitch teeth
– Model: 600886, 11 pieces, 7 saws
– Sizes: 3/4 inch to 2-1/2 inch saws
– Arbors: Hex8 and Hex10 Rapid Core Eject arbors
– Pilot bits: Hex8 and Hex10 HSS pilot bits
– Case: Hard storage case included

How to choose

Pick the blade first. Bi-metal high speed steel is the workhorse for wood, plastic, drywall, and thin metal, and handles nails and rough use. Carbide demands better technique but lasts far longer in abrasive stock, fiber cement, cast iron, and frequent metal. Diamond grit has no teeth and grinds tile, stone, and glass with water cooling, so keep it for facing work, not wood or steel panels.

Next, count sizes you truly need. Gauge holes and cable ports cluster small, while vents and larger conduit need bigger cups. A wide kit like the LENOX 26-piece set avoids gaps, while deeper cups like the DEWALT set suit thick walls. Check depth against your thickest wall.

Then look at the arbor. Quick change mandrels and pin-drive arbors save time and reduce wobble. Clean plug ejection, such as the Spyder design, matters for many holes in a row.

Finally, plan speed. Big cups must run slow. Use the kit speed chart, clamp the work, wear eye protection, and add oil on metal. On stainless, be honest: bi-metal dulls fast there, so use carbide, go very slow, and keep steady pressure with oil, or teeth will glaze and stop cutting. A sharp pilot and cutting oil stretch blade life more than any other habit.

FAQ

Can a bi-metal hole saw cut stainless steel?

It can make an occasional hole in thin stainless if you run very slow, use cutting oil, and keep firm, even pressure. Heat and work hardening are the problems, so repeated stainless work dulls bi-metal quickly. For more than a rare hole, choose carbide and the same slow, oiled technique.

Why does my hole saw leave a rough or oversized hole?

Wobble is the usual cause. A bent or dull pilot, a loose arbor, or an unclamped panel lets the cup wander before teeth score a full circle. Fit a fresh pilot, tighten the arbor, clamp the work flat, and let teeth establish the groove before adding pressure.

How do I make hole saw teeth last longer?

Match speed to diameter, with big cups turning slowly, and lift often to clear chips. Use cutting oil on steel and iron, avoid overheating the edge until it discolors, and store cups in the case so teeth do not bang together.

Do I need a special drill for large hole saws?

A strong drill with a side handle gives best control for large cups, because torque rises sharply if the cup binds. Use low speed and brace for a sudden catch.

Verdict

For one kit on the generator bench, Milwaukee balances durability, coverage, and plug removal for wood and thin metal. Choose DEWALT for deep cuts, LENOX 26-piece for broad diameters, LENOX carbide for abrasive stock, and Spyder for fast plug ejection. Slow speed, a sharp pilot, and oil on metal decide the result most.

Explore Our Guides & Free Tools