🛒 Best Price Today on Amazon
Prime members get fast, free shipping on everything above, plus member-only deals. New members get a 30-day free trial — cancel anytime.
Pulling the side cover off a portable generator rarely calls for a full socket set. The blower housing, control panel, air cleaner box and recoil housing hang on small hex-head screws and nuts, and a nut driver turns them faster than a ratchet. The same tool suits hex screws on worm-gear hose clamps, found on fuel lines and intake boots.
The sizes repeat from machine to machine. Domestic engines lean on 1/4, 5/16 and 3/8 inch hex heads; imported engines and inverter models add 8 mm and 10 mm hardware. Hollow shafts matter because many cover bolts thread onto studs, and a solid shaft bottoms out before the hex seats. Magnetic tips help when a screw hangs over a dark engine bay and the other hand holds the cover.
The five sets below cover the main formats: fixed-handle drivers, magnetic power nut drivers, a multi-bit tool, a bit-bar set, and a metric bundle.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
- Klein Tools 631 — classic 7-piece SAE set with 3-inch hollow shafts; the default pick for cover work.
- Klein Tools 32950 — six magnetic hollow power drivers on 5-inch shafts plus a ratcheting handle; best for drill work.
- Klein Tools 32500 11-in-1 — one handle converting to three nut driver sizes plus eight bits; the grab-and-go pick.
- BLACK+DECKER 71-080 — ten nut driver bits on a storage bar for your spinner handle; the widest SAE size run here.
- Klein Tools 16+7 Piece Bundle — adds a 7-piece metric set covering 8 mm and 10 mm hardware on imported engines.
Klein Tools 631 Nut Driver Set, 7-Piece
The 631 is the set most small-engine benches end up owning. Seven fixed-handle drivers cover 3/16 through 1/2 inch, each on a 3-inch shaft hollow along its full length, so a nut runs down a long bolt or stud without bottoming out. Chrome plating shrugs off grime, and Tip-Ident caps stamp each size on the handle end for quick grabs.
For generator work the middle trio does the daily lifting: 1/4 inch for panel and hose clamp screws, 5/16 inch for housing hardware, 3/8 inch for heavier cover bolts. Cushion-Grip handles break corroded fasteners loose by hand yet keep enough feel for plastic panels. Tips are plain, not magnetic, so work over a tray on vertical covers.
Specs
- Sizes: 3/16, 1/4, 5/16, 11/32, 3/8, 7/16, 1/2 in
- Shaft: 3 in, full hollow
- Finish: chrome plated
- Handles: Cushion-Grip with Tip-Ident size caps
- Format: 7 fixed-handle drivers, non-magnetic tips
Klein Tools 32950 Ratcheting Hollow Power Nut Driver Set
The 32950 takes the power route: six hollow nut drivers on 5-inch shafts that click into the included ratcheting handle or a drill chuck. Each tip carries a rare-earth magnet for one-handed handling, and the 3-3/4 inch hollow depth swallows threaded rod and long mounting studs. The drivers are impact rated and color coded by size.
Hand mode earns its keep on generators. The ratcheting handle gives controlled torque for panel screws that crack under a drill, while drill mode strips a set of cover bolts in seconds during a valve adjustment. The smaller sizes handle daily hardware, and the run to 9/16 inch covers frame and muffler nuts. Counting the handle, the kit holds seven pieces.
Specs
- Sizes: 1/4, 5/16, 3/8, 7/16, 1/2, 9/16 in
- Shaft: 5 in with 3-3/4 in hollow depth
- Magnets: rare-earth magnet in each tip
- Build: impact rated, color coded by size
- Includes: ratcheting quick-connect handle; 7 pieces total
Klein Tools 32500 11-in-1 Screwdriver/Nut Driver
The 32500 folds a small nut driver set into one multi-bit tool. Flip the interchangeable barrel and the handle becomes a 1/4, 5/16 or 3/8 inch nut driver — the sizes behind nearly every cover screw, panel fastener and hose clamp. The other eight functions are bits: Phillips, slotted, Torx and square recess.
Keep this one in the generator’s kit bag rather than on the main bench. One handle replaces a pouch of drivers during an oil change or outage, and the Cushion-Grip grip still delivers honest hand torque. The trade-off is depth: the barrel is not a deep hollow shaft, so nuts far down a stud stop it. For flat covers and clamps, it is the fastest single grab here.
Specs
- Nut driver sizes: 1/4, 5/16, 3/8 in
- Bits: #1 and #2 Phillips, 3/16 and 1/4 in slotted, T10 and T15 Torx, #1 and #2 square
- Format: interchangeable barrel with onboard bit storage
- Handle: Cushion-Grip
- Model: Klein Tools 32500
BLACK+DECKER 71-080 Nut Driver Set, 10-Piece
The 71-080 is a bit-bar set: ten nut driver bits on a slim storage bar, no handle in the box. The bits drop into a spinner handle or bit holder you already own, or into a drill driver at low speed. The size run is the widest here, 5/32 to 1/2 inch in fine steps, suiting mixed hardware on older generators and aftermarket covers.
The bits are short and non-magnetic, so the set suits bench work and short screws rather than deep housings or long studs. Its strength is tidiness: the bar keeps all ten sizes in order, ready to pair with whatever handle is at hand. Own a good spinner handle, and this gives it a full SAE range.
Specs
- Sizes: 5/32, 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2 in
- Format: nut driver bits on a storage bit bar
- Handle: none; fits bit holders and spinner handles
- Tips: non-magnetic
- Model: BLACK+DECKER 71-080, 10 pieces
Klein Tools Screwdriver, Nut Driver and Metric Nut Driver Set (16+7 Pieces)
This bundle pairs a 16-piece screwdriver and nut driver set with Klein’s 7-piece metric nut driver set, closing the gap SAE-only kits leave open. The metric drivers cover 5 through 10 mm on 3-inch chrome-plated hollow shafts. The 8 mm and 10 mm sizes matter most: imported engines, inverter generators and European-built panels use them for covers, housings and clamps.
Running both a domestic standby unit and an imported inverter? One bundle ends the two-system shuffle. The metric hollow shafts slide over stud-mounted covers like the SAE drivers, and the bundled screwdrivers handle the fasteners beside the hex hardware. It takes the most bench space here, but leaves no common fastener uncovered.
Specs
- Contents: 16-piece screwdriver/nut driver set plus 7-piece metric set
- Metric sizes: 5, 5.5, 6, 7, 8, 9, 10 mm
- Metric shafts: 3 in, hollow, chrome plated
- Total pieces: 23
- Brand: Klein Tools bundle
How to choose
Match the set to your machines first. Domestic generators live on 1/4, 5/16 and 3/8 inch hardware, so any SAE set here works; add metric coverage if an imported engine or inverter shares the garage, since 8 mm and 10 mm fasteners appear on their covers.
Hollow depth comes next. Cover bolts on studs, and nuts on threaded rod, need a shaft that passes over the stud; the 3-inch hollow shafts and the deeper 32950 handle these, while bit-bar sets and multi-bit barrels suit short screws only. Magnetic tips earn their place over a dark engine bay; on a clean bench, plain tips are fine.
Finally, pick the format. Full drivers give the best feel and hand torque. A spinner handle with bits packs smaller and swaps sizes quickly. Power drivers add drill speed for long cover pulls, but finish panel screws by hand so plastic housings stay intact.
FAQ
What nut driver sizes fit most generator covers?
The 1/4, 5/16 and 3/8 inch sizes cover most covers, housings and panels on domestic machines, and fit most hose clamp screws. Imported engines and inverters add 8 mm and 10 mm hardware.
Do I really need hollow shafts?
If a cover bolt threads onto a stud, yes. The hollow shaft passes over the stud so the hex seats fully; a solid shaft or short bit bottoms out and rounds the fastener.
Are magnetic tips worth having?
They help when a screw comes out above a dark engine bay, since the magnet keeps the fastener on the tip one-handed. On a bench with a parts tray, plain tips work just as well.
Should panel screws be run in with a drill?
Spin fasteners out with the drill and run them down loosely, then finish by hand. Hand torque keeps plastic panels and threaded inserts from cracking under a power driver.
Verdict
For most owners, the Klein Tools 631 is the set to buy first: full hollow shafts, the right SAE sizes, handles that survive bench work. Choose the 32950 for magnetic, deep-hollow drivers with a ratcheting handle. Add the bundle when metric hardware shares the garage, keep the 32500 in the generator’s bag for outages, and let the BLACK+DECKER bar round out a spinner handle kit.





Write Your Review
No reviews yet. Be the first to share your experience!