⏱ 7 min read  ·  ✅ Updated Nov 2026

Thick timber does not forgive the wrong bit. A spade bit wanders, a twist bit packs its flutes and stalls, and a hole saw leaves you chiseling plugs out of a beam. An auger bit works differently: a threaded screw tip pulls the bit forward on its own, cutting edges shave the wood, and a deep open flute carries chips up and out as you drill. That is why augers remain the go-to choice for beams, landscape timbers, and pole work.

Our top pick: IRWIN Ship Auger Bit 1-1/16 Inch x 17 Inch (4935572). Runner-up: DEWALT Ship Auger Bit 3/4 Inch x 17 Inch (DW1683).

The five bits below cover the main shapes: long ship augers for stacked timbers, a short Daredevil-style bit for fast framing holes, and a solid-center design for cleaner walls in dry hardwood. All use hex shanks for high-torque drills, and all demand respect: a self-feeding bit can bind, and when it binds the drill tries to twist in your hands.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

For most deep work in softwood and landscape timbers, the DEWALT DW1683 in 3/4 inch by 17 inch is the balanced pick. Need a bigger hole for bolts through beams? The IRWIN 4935572 ship auger at 1-1/16 inch by 17 inch is the classic long-reach option. For nail-embedded wood, the Diablo DAG3110 uses a hardened two-flute design. The Bosch NKST20 Daredevil is the short, fast choice for joists, while the Crescent CDAG-1749 suits wide holes where a clean wall matters more than speed.

IRWIN Ship Auger Bit 1-1/16 Inch x 17 Inch (4935572)

This is a true ship auger: a single deep flute on a long body, topped with a coarse self-feed screw tip. The open throat of that single flute is the point. Green wood and sappy softwood throw off long, damp chips that choke tighter designs, and the wide channel here gives those chips room to travel up and out instead of packing tight.

At 17 inches, it bores through stacked 6×6 timbers without an extension, avoiding extension wobble. The size suits bolts and pipe runs in pole work around generator pads. The trade-off is finish: it cuts fast but leaves a rougher wall than a double-flute design, and its coarse tip pulls hard, so keep a firm two-handed grip as it breaks through.

Specs
– Diameter: 1-1/16 inch
– Overall length: 17 inches
– Flute style: single-flute ship auger, open throat
– Tip: coarse self-feed screw tip
– Shank: 7/16 inch hex
– Model: 4935572

DEWALT Ship Auger Bit 3/4 Inch x 17 Inch (DW1683)

Three-quarter inch is the hole most people actually need in thick timber: big enough for common bolts with clearance, small enough that the drill is not fighting a huge cutting circle. The DW1683 self-feed pilot tip draws the bit through the wood, so you guide rather than push.

Its flute is shaped to move chips out of deep holes, where lesser bits fail. Chip evacuation decides whether you finish in one pull or stop every few seconds to clear the hole. The hardened edge also holds up better against hidden nails. Run it in low gear on a high-torque drill, and back it out partway every few inches in resinous wood to empty the flute.

Specs
– Diameter: 3/4 inch
– Overall length: 17 inches
– Flute style: ship auger with polished chip channel
– Tip: self-feed pilot screw tip
– Shank: 7/16 inch hex
– Model: DW1683

Bosch Daredevil Auger Bit 1-1/4 Inch x 7-1/2 Inch (NKST20)

The NKST20 is the sprinter here. At 7-1/2 inches overall, this Daredevil bit is built for speed in joists, studs, and beams up to about 6 inches thick rather than for extreme depth. Its dual cutting edges and reinforced screw tip pull it through wood quickly, and the wide flute throws chips out behind it so the hole stays clear.

That speed has limits. You cannot reach through a doubled beam in one pass with a bit this short. Treat it as the bit for repetitive holes in framing, deck ledgers, and generator platforms. The 1-1/4 inch diameter is generous for conduit, pipe, and large bolts. Fit the side handle: a wide bit feeding this fast can catch on a knot, and the reaction torque arrives without warning.

Specs
– Diameter: 1-1/4 inch
– Overall length: 7-1/2 inches
– Flute style: dual-edge Daredevil, wide chip channel
– Tip: reinforced self-feed screw tip
– Shank: 7/16 inch hex
– Model: NKST20

Diablo Auger Bit 1 Inch x 17-1/2 Inch (DAG3110)

Diablo built the DAG3110 for nail-embedded framing and old beams with mystery hardware inside. Its hardened Dura-Tip screw point is made to survive nail strikes, and the two-flute body gives a more balanced cut than a single-flute ship auger, so the wall comes out cleaner over a 13-1/2 inch working length.

That suits work around existing structures, including generator skids and pads, where you may drill near old fasteners without knowing it. The 1 inch diameter handles common bolt and conduit sizes, and the hex shank locks into quick-change chucks without spinning. A two-flute design packs sooner in wet, stringy wood, so back it out to clear chips more often there.

Specs
– Diameter: 1 inch
– Overall length: 17-1/2 inches
– Working length: 13-1/2 inches
– Flute style: two-flute with hardened Dura-Tip
– Shank: 7/16 inch hex
– Model: DAG3110

Crescent Solid Auger Bit 1-1/4 Inch x 17 Inch (CDAG-1749)

The CDAG-1749 takes the older solid-center idea and stretches it to a full 17 inches. A solid-center auger carries a central shaft with edges that scribe the rim of the hole before the main cutters lift the waste. That scribing action leaves a smoother, rounder hole in dry hardwood, where a ship auger can tear the entry and exit.

Choose it when the hole will be seen or a bolt must fit snugly: gate posts, pergola timbers, and hardwood beams. The fine screw tip feeds at a measured pace in hard, dry wood, giving more control near the exit face. It is not the fastest bit here, and its tighter flute can load up in green, sappy softwood. In the right material, though, it produces the cleanest deep hole of the five.

Specs
– Diameter: 1-1/4 inch
– Overall length: 17 inches
– Flute style: solid-center with rim-scribing edges
– Tip: fine self-feed screw tip
– Shank: 7/16 inch hex
– Model: CDAG-1749

How to choose

Match the flute to the wood first. Single-flute ship augers clear chips best in green, wet, or sappy timber and in very deep holes. Double-flute and solid-center designs cut a cleaner wall in dry wood and suit visible holes or tight fittings.

Look at the screw tip next. A coarse thread pulls hard and fast in softwood but can feel grabby and can split thin stock near an edge. A fine thread feeds more gently, suits dry hardwood, and gives finer control near the far face.

Length should clear your thickest timber in one pass, with the shank still held firmly in the chuck. The 17 inch class handles doubled beams and stacked timbers; short bits are happier in single joists and studs. Every bit here uses a 7/16 inch hex shank, which resists spinning and suits high-torque drills. A wide auger in hardwood also needs low gear and a side handle; if the drill struggles, drop a diameter size.

FAQ

Why does my auger bit try to twist the drill out of my hands?
The screw tip feeds on its own, so a knot or nail can bind the bit instantly while the drill keeps turning. Use low gear, fit the side handle, and release the trigger the moment the feed changes.

Should I choose a coarse or fine screw tip?
Coarse tips suit softwood, green timber, and fast rough work because they pull the bit in quickly. Fine tips suit dry hardwood and work near edges or finished faces, where a gentler feed means less splitting and less tear-out.

How do I keep a deep hole straight?
Sight the drill from two directions for the first inch; the entry angle is the angle you keep. Let the tip establish the path, avoid side pressure, and clear chips often. A clamped guide block helps on critical bolt holes.

When is an auger the wrong tool?
In thin sheet goods, plywood, and end grain, an auger can tear or grab. Use a spade bit, Forstner bit, or hole saw there instead.

Verdict

For a single bit to keep with the timber tools, take the DEWALT DW1683: its size covers the most bolt holes in beams and landscape timbers, and it clears chips well at depth. Add the IRWIN 4935572 for wider holes through stacked stock, and the Diablo DAG3110 when the wood may hide nails. The Bosch NKST20 earns its place for fast framing holes, and the Crescent CDAG-1749 is the finisher for clean holes in dry hardwood. Pair them with a strong drill and steady grip.

Explore Our Guides & Free Tools