🛒 Best Price Today on Amazon
Prime members get fast, free shipping on everything above, plus member-only deals. New members get a 30-day free trial — cancel anytime.
- Quick answer
- Bosch DSB5013P 13-Piece Daredevil Spade Bit Set
- IRWIN SPEEDBOR Blue-Groove Pro Spade Bit Set, 17-Piece
- IRWIN SPEEDBOR Spade Wood Drill Bit Set, 5 Piece
- Ansen Tools AN-304 Extra Long 16 Inch Spade Bit Set, 6 Piece
- Century Drill and Tool 36488 Lazer Spade Bit, 1-3/8 Inch
- How to choose
- FAQ
- Verdict
Running cable through a framed wall is rough-in work, and the tool that does most of it is a flat paddle with two sharp corners. A spade bit bores a wide hole through a stud in seconds and shrugs off abuse that would dull a finer cutter. Around a generator install that means holes for feeder cable, conduit, and control wiring through plates and joists.
Not all paddles cut the same way. A plain flat edge scrapes through, a spur-and-brad design scores the rim first for a cleaner entry, and a threaded cone tip pulls itself forward so the drill does less pushing. Shank length matters too: a short bit suits open framing, while a long bit reaches between studs and through stacked plates. The five picks below cover those main styles.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
For most rough-in work, pick the Bosch Daredevil set: its threaded tips pull fast and the pouch covers common sizes. The IRWIN 17-piece Pro set is the wider case-based option. The IRWIN 5-piece set covers core sizes in less bulk. The Ansen set solves reach problems, and the Century single fills the big 1-3/8 inch hole.
Bosch DSB5013P 13-Piece Daredevil Spade Bit Set
The Daredevil design is built around a full-cone threaded tip. The cone screws itself into the wood and draws the paddle behind it, so holes through double plates and dense studs take less arm pressure. A spur and reamer edge scores the circumference before the flat lifts the core, leaving a tidier rim than a plain paddle.
The set covers common sizes up through 1-1/2 inches and rolls up in a pouch. Each bit rides on a 1/4 inch hex shank with a power groove, locking into quick-change holders and impact drivers.
Speed is the trade here. Ease off near breakthrough or the exit face will tear. Feed steadily and let the thread do the work.
Specs
– Model: DSB5013P, 13-piece set in pouch
– Tip: full-cone threaded self-feed tip
– Edges: spur and reamer corners for cleaner rims
– Shank: 1/4 inch hex with power groove
– Sizes: range up to 1-1/2 inches
– Use: fast boring in wood and treated lumber
IRWIN SPEEDBOR Blue-Groove Pro Spade Bit Set, 17-Piece
IRWIN takes a different route to speed. The Blue-Groove point and edge open a channel through the paddle, giving chips somewhere to go instead of packing around the shank. Double cutting spurs scribe the outside of the hole, reducing breakout on the far face when the bit is kept square.
Seventeen pieces in a case is the appeal for a shop kit: the spread covers small control-wire holes through to wide bores for pipe, and the case protects edges in transit. The hex shanks are grooved to resist slipping.
These are scraping edges, so the operator sets the pace. That gives more control in thin stock, at the expense of more push on deep holes. Withdraw often to clear the groove.
Specs
– Model: 1792761, 17-piece set with storage case
– Point: Blue-Groove point for fast chip removal
– Edges: double cutting spurs to reduce breakout
– Shank: 1/4 inch grooved hex, quick-change fit
– Length: standard length bits for open framing
– Use: rough boring in softwood, hardwood, and plywood
IRWIN SPEEDBOR Spade Wood Drill Bit Set, 5 Piece
This five-piece IRWIN set trims the idea down to the core sizes most generator and framing jobs actually use. It shares the Speedbor family shape: a Blue-Groove point, double spurs that score the rim, and a 1/4 inch hex shank that fits drills and quick-change adapters.
A small set makes sense when the work is focused. Running a feeder through a short run of studs rarely needs a dozen diameters. Five bits ride light and leave room for long bits and extensions.
The limit is obvious: an odd size means a trip for a single. Measure the bundle first, including jacket and any grommet, and confirm the set covers it with a little clearance.
Specs
– Model: 88885, 5-piece set
– Point: Blue-Groove point and cutting edge
– Edges: double cutting spurs for reduced breakout
– Shank: 1/4 inch hex, fits quick-change chucks
– Length: standard 6 inch class bits
– Use: everyday rough holes in framing lumber
Ansen Tools AN-304 Extra Long 16 Inch Spade Bit Set, 6 Piece
Reach is the whole point of this Ansen set. At 16 inches long, these bits bore where a short bit and drill body will not fit, pass through stacked plates in one go, and line up holes across joists from one position. For retrofit cable runs around an existing generator pad or panel, that reach avoids opening extra wall.
Six pieces cover the middle sizes used for cable and small pipe. The flat paddle is the classic scraping design, simple to resharpen with a file. The long shank flexes under side load, so a steady, aligned feed matters.
Long bits wander if pushed hard or run at an angle. Keep the drill square to the face and pull back often to clear chips. Never force a bent long bit; a mild wobble at the chuck becomes a wide, rough hole at the tip.
Specs
– Model: AN-304, 6-piece set
– Length: 16 inches for deep and between-stud reach
– Form: flat paddle, classic scraping edge
– Shank: hex shank for chuck and holder use
– Sizes: six common mid-range diameters
– Use: retrofit runs, stacked plates, deep joists
Century Drill and Tool 36488 Lazer Spade Bit, 1-3/8 Inch
Sometimes the job is one big hole, done repeatedly. This Century Lazer single is a 1-3/8 inch paddle, the size crews reach for when a bundle or larger conduit needs real clearance through a stud. Buying the single in the size you use beats carrying a wide set whose other diameters sit idle.
The Lazer line bores a defined hole with less pressure, using a pointed center and corners that score before the flat clears the core. Edge condition is everything: a sharp corner cuts, a rounded corner burns. Dress the edge with a file when holes smoke.
A wide paddle needs torque and respect. Use a drill with a side handle, brace for the moment the spurs bite, and back the work when the far face matters. One hidden nail will chip an edge in an instant, so keep a spare single.
Specs
– Model: 36488, single bit
– Diameter: 1-3/8 inches
– Length: 6 inch class standard length
– Shank: 1/4 inch hex
– Form: Lazer spade design for defined holes
– Use: large cable bundles and conduit pass-throughs
How to choose
Match the style to the cut first. Threaded self-feed tips are fastest in thick framing but demand a light touch near breakthrough. Spur-and-brad and Blue-Groove designs give more control and a cleaner rim. Plain long paddles win on reach, not finish.
Size the hole to the bundle, not the cable alone. Add the jacket and sleeve, then choose a bit a step larger. Too tight a hole skins insulation during the pull; too loose a hole may breach framing rules for bored studs.
A 1/4 inch hex shank swaps between drill and impact driver and locks into extensions. Keep one long extension for retrofit work, and remember that every added joint adds wobble.
Finally, plan for tear-out and nails. Back the work with scrap, or finish from the other side. Bore unknown framing slowly, and keep singles of your main sizes as spares.
FAQ
Why does the back of the hole always tear out?
The spurs lose support as they exit, so fibers lift instead of cutting. Backing the piece with scrap, easing pressure at breakthrough, or finishing from the far side keeps the exit cleaner.
Can I use a spade bit in an impact driver?
Yes, when the bit has a 1/4 inch hex shank with a power groove, as the sets above do. A drill still offers finer control near breakthrough and in thin material.
What size do I need for generator feeder cable?
Measure the full bundle, including jacket and sleeve, then pick the next bit size above it. Common picks land in the 3/4 to 1-3/8 inch range, but the bundle decides.
How do I keep a long bit drilling straight?
Keep the drill square, use light steady pressure, and clear chips often. A long shank flexes under side load, so correct the angle early rather than steering mid-hole.
Verdict
For a main kit, the Bosch Daredevil set earns its place with self-feed speed and a pouch that travels well. The IRWIN 17-piece Pro set suits a case-based shop setup, while its 5-piece sibling covers focused jobs with less bulk. Add the Ansen long set when reach is the problem, and keep the Century single sharp for big pass-throughs.





Write Your Review
No reviews yet. Be the first to share your experience!